Page Comparison

09 65 19 Carpet Tile Luxury Vinyl Tile (LVT)

LVT Shall be installed as per the most current version of the manufacturer's recommendations, and guidelines, including for subfloor preparation, installation conditions and methods. All LVT shall be selected from the list of approved Penn State styles.

Overall product requirements:

1. Minimum 20 mil wear layer
2. Minimum 20-year commercial warranty (some of the lines included/listed may only have an advertised warranty of 15 years, manufacturer must increase warranty to 20 for Penn State to qualify product)
3. EPD and/or HPD disclosure on product
4. Floorscore Certified
5. Product can be part of a recycling program
6. Glue-down installation

Specific manufacturer information:

1. Tartkett

   1. 1. 1. Techtonic finish only

         2. Contour & ID Latitude Series
            1. If recycling is a requirement, ID Latitude & Color Play are not part of their Restart program.
         3. No Course Emboss: Rough Grain (RG) or Sawn (SW)
         4. Recyclability: product part of ReStart program.
2. Mannington:

   1. 1. 1.  Quantum Guard Elite finish only

         2.  Lines excluded: No Reservations (floating), Mannington Crown (floating, no HPD), City Park (floating, no HPD), Mixed Monolith (no HPD, no Floorscore), Spacia First, Spacia First 20, Cirro (Cirro is not included due to its lack of warranty [10-year])

         3. Recyclability: can be part of regrind program at Madison, GA via Vision Resources (3.1.3, 3.1.4,3.1.5)

3. Interface:

   1. 1. 1. Ceramor finish only

         2.  Line excluded: Steady Stride

         3. Recyclability: product part of ReEntry program Recycled into carpet backing. Product contains 39% pre-consumer recycled content.

09 68 10 Carpet Tile

Note: Carpet tiles only shall be specified and installed; broadloom carpet is not allowed. Any deviation or exception to this must be approved in writing by the Assistant Vice President of the Office of Physical Plant.

1. Carpet shall be installed as per the most current version of the manufacturer’s recommendations, and guidelines, including for subfloor preparation, installation conditions and methods. All carpet shall be selected from the list of approved Penn State styles

1. InterfaceFLOR, 1503 Orchard Hill Road, LaGrange, Georgia, 30240
1. Penn State website:  http://contracts.interface.com/Penn-State
2. Tarkett

1. .  Styles for InterfaceFLOR are available on the listed manufacturer’s website.  Styles for Tarkett must be received from The Account Executive (Michael Albert) who can be contacted at the email address below.

InterfaceFLOR

Kelly Ayres (Giese)

Account Executive | Central Pennsylvania

kelly.ayres@interface.com | cell: 717.815.0194

Customer Service +1 800-634-6032

Follow us on Instagram! | @interface_centralPA

Interface® | interface.com

FLOR | flor.com/commerical

nora by Interface® | www.nora.com

https://psu.guides.interface.com/subscriberLogin?next=https%3A%2F%2Fpsu.guides.interface.com%2Fpsu-products-standards%3Fkey%3DjuyxSY5yTlmTcnat

Tarkett

Michael Albert, Account Executive

Michael.albert@tarkett.com

1010 Wisconsin Avenue NW

Washington, D.C. 20007

Ph: 202-298-4420

Cell: 717-439-2963

Installation Guidelines

1. Carpet Tile shall be installed via full adhesive coverage, with the following notes:  sloped/inclined sloped/inclined surfaces  (regardless of slope), raised floors over pressurized plenum, vertical surfaces, stairs, areas subject to heavy rolling loads (all these areas will require the use of  pressure sensitive glue, per the manufacturer’s specifications

1. ). 
2. No wet set applications will be permitted to be employed the installation process in the so noted areas.
3.  All glues must be water based, zero calculated VOC’s, and contain no toxic or hazardous ingredients.

2. Solvent/petroleum based glues are prohibited.

1. The adhesive must be formulated to facilitate release and re-bonding of carpet tiles while permanently retaining its tack, allowing individual tiles to be lifted out easily and replaced without substantial loss of adhesive properties for the life of the installation.

2. Spare glue and glue containers must be recyclable.