.01 Finish Hardware Requirements

Office Doors:

Locks shall be one of the following:

Sargent #8205 WTJ.
Best 45H7A3J
Schlage L9050 03L

No door closers unless required by current applicable codes.
Office suites main entrance door may use cast iron or aluminum body closer if requested by occupants.

Classroom Doors:

Locks shall be one of the following:

Sargent 8237 WTJ
Best 45H7R3J
Schlage L9070 03L

Door closers shall be one of the following:

Cast iron body (preferred): Lecture Halls (more than 75 occupants)

LCN 4010/4111
DormaKaba QDC115
Sargent 281

Cast aluminum (extra heavy duty) body may be used for classrooms 49-75 occupants:

BestHD8000
Sargent 351
Norton 7500

Cast aluminum (heavy duty) body may be used for classrooms under 50 occupants:

Best HD7000
Sargent 1430
Norton 8500
LCN 1450

Inactive leaf of double doors shall have mortise flush bolts head and foot

Rockwood 555
Trimco 3975
Ives 457

See Division 13 20 10 for further references to the General Purpose Classroom document that includes information on doors and hardware.

Laboratory Doors:

Locksets and trim shall be one of the following:

Sargent #8225 WTJ.
Best 45H7T3J
Schlage L9453 03L

Door closers shall be one of the following:

Cast iron body (preferred):

LCN 4010/4111
DormaKaba QDC115
Sargent 281

Cast aluminum (extra heavy duty) body may be used for undergraduate labs:

Best HD8000
Sargent 351
Norton 7500

Cast aluminum (heavy duty) body may be used for graduate labs:

Best HD7000
Sargent 1430
Norton 8500
LCN 1450

Inactive leaf of double doors shall have mortise flush bolts head and foot

Rockwood 555
Trimco 3915
Ives 457

Storage Room Doors:

Locks shall be one of the following:

Sargent 8204 WTJ
Best 45H7D3J
Schlage L9080 03L

No door closers unless required by current applicable codes or facility programming requirements.

Janitor Closet, Janitor Storage, and Utility Room Doors:

Locks shall be one of the following:

Sargent 8204 WTJ
Best 45H4D3J
Schlage L9080 03L

No door closers unless required by current applicable codes or facility programming requirements.

Public Toilet Doors:

At public restrooms with multiple stalls, doors shall be equipped with stainless steel push/pulls:

Rockwood BF110 x 70C
Ives 8302-10
Trimco 1018-3B with matching push plates, minimum 18 ga, sized 8" x 16"

Door closers shall be one of the following:

Cast iron body (preferred):

LCN 4010/4111
DormaKaba
Sargent 281

Cast aluminum (extra heavy duty) may be used for single user toilet rooms:

Best HD 8000
Sargent 351
Norton 7500

Provide kickdown holder where current applicable code permits:

Rockwood 461
Ives FS452
Trimco 1220

Communicating Doors:

Locks shall be one of the following:

Sargent 8226 WTJ
Best 45H7G3J
Schlage L9466 03L

No door closer, unless required by current applicable code.

Stair Tower Doors:

Exit devices and trim for single doors shall be one of the following:

Von Duprin #98L-F-BE x 996L-R-03
Precision FL-2114 x 4914C
Sargent 8815 x 715ETJ

Exit devices and trim for paired doors shall be one of the following:

Von Duprin #9827L-BE-LBR x 996L-R-03
Precision FL-2214LBR x 4914C
Sargent NB8715 x 715ETJ

No bottom latch or rod; Provide standard fire bolt to be installed 12" up from bottom of doors between pairs.

OPERATION: exit by push bar, always free; entry by lever, always free
Door closers shall be one of the following:

LCN 4010/4111
DormaKaba QDC100
Sargent 281

Hold open arms are not allowed on fire rated door. If hold-open function is desired, wall mounted magnetic holder tired into the fire alarms system shall be used:

Rixson 997
LCN SEM7840
Dorma em504

A. Exterior Aluminum Doors (narrow lock stile):

Exit devices for single doors shall be one of the following:

Von Duprin 33NL x 3982-6
Precision 2403 x Trimo 1191-4N
Sargent AD8405 x 862

At paired doors, use exit devices as listed above in conjunction with removable mullion:

Von Duprin 4954
Precision 822
Sargent 980

Prefer to not use surface vertical rod devices at exterior pairs, unless absolutely required for usage (if used, vertical rod extended latch guard is required). Do not use concealed vertical rod exit devices in any application.
Operation: Egress by inside push bar, always free. Entry by key or card reader, which would retract latch and allows door to be pulled open. Do not provide cylinder dogging (unless facility security programming allows) to allow for push-pull operation.
Door closers shall be one of the following:

LCN 4010/4111
Stanley QDC100
Sargent 281

B. Exterior Hollow Metal Doors (wide lock stile)

Exit devices for single door shall be one of the following:

Von Duprin 99NL x 392-6
Precision 2103 x Trimco 1191-4 N
Sargent 8805 x 862

At paired door, use exit devices as listed above in conjunction with removable mullion:

Von Duprin 4954
Precision 822
Sargent 980

Prefer to not use surface vertical rod devices at exterior pairs, unless absolutely required for usage (if used, vertical rod extended latch guard is required). Do not use concealed vertical rod exit devices in any application.
Operation: Egress by inside push bar, always free. Entry by key or card reader, which retracts latch and allows door to be pulled open. Do not provide cylinder dogging (unless facility security programming allows) to allow for push-pull operation.
Door closers shall be one of the following:

LCN 4010/4111
Dorma Kaba QDC100
Sargent 281

Vestibule Doors:

Each door will have dummy push-pull bar to match exterior:

Von Duprin 330 x 392-6
Precision 671 DR x Trimco 1191-4 N
Sargent 8893 x 862

Door closers shall be one of the following:

LCN 4010/4111
Dorma Kaba
Sargent 281

NOTE: select exterior opening applications may warrant an in-ground closer. In-ground Rixson closers maybe used where doors are located under covered entrances away from the elements, subject to review from OPP. Vestibule and interior applications may use in-ground Rixson closers. Model shall be heavy duty, and specific to door characteristics and/or other facility requirements.

Low Energy Power Openers (section 08 71 13 included for quick reference)

Norton 6000 series
LCN 4600 series
Dorma 250 Series
Finish shall compliment the opening's frame and/or closers in the surrounding area.
Actuator shall be by the above manufacturers or Larco.

wireless actuators shall only be used on interior applications

Bollards shall be minimum 42-inches high by 5-inches square and able to accept the push plate actuator, card reader and proximity reader. Color to be approved by Office of Physical Plant (OPP) before project bid phase.

Residence Hall Bedroom Doors:

Locksets shall be one of the following:

Sargent 8225 WTJ
Best 45H7T3J
Schlage L9453 03L

Door closers shall be one of the following:

Cast iron body (preferred):

LCN 4010/4111
Dormakaba QDC100
Sargent 281

Cast aluminum (extra heavy duty) may be used:

Best HD8000
Sargent 351
Norton 7500

Kickplates and mop plates shall be 18 ga stainless steel with beveled edges.

Uncontrolled Exit Doors:

All doors shall be equipped with proper exterior door hardware as listed above with an emergency exit alarm:

Detex EAX-500
Alarm Lock PG21

Emergency exit alarms will be armed with a small-format cylinder installed in alarm case. Where required for usage, also provide exterior rim cylinder to allow for arming/disarming alarm from outside.
Exit alarms are battery operated (where applicable with prior approval).

Lock Cylinders:
A. For new building construction: All lock cylinders shall be 7-pin small-format interchangeable core (SFIC), ANSI/BHMA A156.5, Grade 1 Certified Products Directory (CPD) listed cylinders employing a utility patented and restricted keyway requiring the use of a patented key.
1. Keying / supply options:

a. Specification which list keying by the university Lock Shop, provide the following uncombinated, or 0 bitted, small format cores:
i. Provide Medeco (MC) X4
ii. No substitutions.
b. Specifications which require factory keying (restricted to Housing and Food Services only)
i. Provide Medeco (MC) X4
ii. No substitutions
B. For fully renovated buildings or full building re-cores: All lock cylinders shall be 7-pin small-format interchangeable core (SFIC), ANSI/BHMA A156.5, Grade 1 Certified Products Directory (CPD).
Keying / supply options:
c. Specification which list keying by the university Lock Shop, provide the following uncombinated, or 0 bitted, small format cores:
i. Provide Medeco (MC) X4
ii. Alternate core/key manufacturer exception requests will be directed to the Director of Physical Security, University Police & Public Safety for approval or denial. Requests will provide justification for the use of an alternate manufacturer.
d. Specifications which require factory keying (restricted to Housing and Food Services only)
i. Provide Medeco (MC) X4
ii. No substitutions
C. For a partial renovated building: For partially renovated spaces, the Lock Shop, in partnership with the Planner/Estimator, will determine the manufacturer and keyway to match the current system, within the building.
2. All keys shall be embossed with the letters “PSU” and “DO NOT DUPLICATE”.
a. For factory keying, keys will also have a key identifier with key symbol directed by the University.
3. Contractors will remove their construction cores for installation of permanent cores. This will be managed and coordinated by the Project Manager or Construction Services Rep, for Physical Plant.
4. All key operated elevator switches will be provided with SFIC, to match the current key systems. The OPP Lock Shop will determine the manufacturer, based on the need for the switch.
5. All small format cylinders and cores will be furnished under the Finish Hardware Section.
Electric strikes

HES: Cylindrical/Mortise locks 1006

Rim exit devices 9600

Von Duprin: Cylindrical/Mortise locks 6200 series

Rim exit devices EN800 series

RCI cylindrical/Mortise Locks F2164

RCI Rim exit devices (F) 0162

Hinges:

All doors shall be equipped with proper size, type and number of hinges. Provide non-removable pins at exterior doors and interior secure doors swinging out.
Interior doors up to 36" wide shall be provided with one of the following:

Best FBB179
McKinney TA2714
Ives 5BB1

Interior doors over 36" wide shall be provided with one of the following:

Best FBB168
McKinney T4A3786
Ives 5BB1HW
(extra heavy weight)

Exterior doors shall be provided with one of the following:

Best FBB199
McKinney T4A3386
Ives 5BB1HWSS
(stainless steel extra heavy weight).

Continuous Hinges maybe used in lieu of "butt" hinges where the application would warrant enhanced durability /aesthetics.

Best 661 HD
Pemko CFM83 SLF HD
Ives 112 HD

Door Stops, Holder and Bumpers:

Doors that open to a perpendicular wall shall be provided with wall mounted stop:

Ives WS406/407
Rockwood 406/409
Trimco 1270WV/WX

Where required, floor mounted stop to be:

Rockwood 442
Ives FS438
Trimco W1211

Where neither floor or wall stops are applicable, provide overhead track stop:

Surface mount heavy duty:

Glynn Johnson 90
Rixson 9-x36
Dorma 900 series

Surface mount standard duty:

Glynn Johnson 450
Rixson 10-x36
Dorma 700 series
(use at closets and low-use doors)

Concealed mount heavy duty:

Glynn Johnson 100
Rixson 1-x36
Dorma 910 690
(use at doors with Parallel Arm push side door closers)

Do not specify automatic holders at exterior doors.

Finishes:

Standard finishes as follows:

Interior hinges, locks, floor stops: US26D/652 Satin Chrome.
Exterior hinges, push-pulls, kickplates, exit devices: US32D/630 stainless steel.
Doors closers and accessories: 689 / AL powder coat aluminum finish.
Other finishes may be warranted to match existing and need prior approval.

Miscellaneous Requirements:

SUBSTITUTIONS: This standard allows for three (3) solutions from unique corporations for all major items (hinges, locksets, exit devices, door closers and cylinders). In order to maintain quality on the campus, the University will not accept any alternates or substitutions to these items as specified above, unless prior written approval from Office of Physical Plant (OPP) is granted.
Doors with push-pulls in conjunction with a cylinder deadlock will be drilled for cylinders.
Provide rubber silencers at all hollow metal frames that do NOT receive sound seal or smoke gasket: Rockwood 608 or Ives 20.
If required, any padlock supplied to be small-format 7-pin key system to match existing.
Furnish padlocks for all transformer gates.
Provide kickplates at any door scheduled with a door closer.
Wood doors that are schedule with door closers to have sufficient blocking built in to meet a 1,000,000 slam cycle test. Thru-bolting of door closers is not acceptable.
Flush bolts should be installed in edge of door.
All push plates should be 8" x 16" unless not possible because of size constraints.
All hardware to be installed according to manufacturer's recommendations unless specified for an atypical installation.

Page Navigation

Related Files

	File	Modified

Browser not supported